ABOUT

Solutions & Cases

Our Case
  • Dynamic Analysis on Hammer of a Coal-Hammer Mill Crusher

    6. Overall dimensions of Crusher and its weight. 4. Data considered for Design 1. Type of material being crushed coal 2. Size of material 200 mm taken to 30 mm crush size 3. Capacity / thorough put 16 to25 ton/hour 4. Type of feeding from top 5. Motor rotational speed 970 rpm 6. Overall dimensions of Crusher 980*890*570 mm

  • Jaw Crusher Destroyer Design Capacity Ton of Coal

    Motor power required to crush coal menghancurkanuntuk if a round jaw crusher is 135 rpm and the energy required to crush coal by Equation 4 is 257.6 joules, then the motor power required is: P = = 4.125 Watt = 5.5 HP 3.1 Design of Transmission Belts Design belt transmission for jaw crusher machine based on the input rotation (n1) at 1400 rpm,

  • Coal Crusher Vibration & Dynamic Forces Caused By Misalignment

    Route Spectrum 11-Jul-05 08:04:30 OVERALL= .7287 V-DG PK = .7267 LOAD = 5.0 RPM = 1799. (29.98 Hz) 0 1000 2000 3000 4000 10-4 10-3 10-2 10-1 10 0 10 1 Frequency in CPM PK Velocity in In/Sec Freq: Ordr: Spec: 440.63 .245 .649 Note indication of a resonance between 1X & 2X Crusher Shaft RPM. Expand to Display 4000 CPM Fmax

  • Dynamic Characteristics of Crusher Supporting Structures

    crushed coal is finally discharged through chutes onto another conveyor belt which leads it finally to the stock yard. DESIGN CONSIDERATIONS FOR SUPPORTING STRUC­ TURES Location Crushers are usually located at a height of say 15m above ground to facilitate easy feeding of coal from the overhead conveyors. The supporting structure is

  • Coal Crusher Coal Impactor MCI-500 Manufacturer from

    Types Of Crusher: COAL IMPACTOR: Condition: New: Motor Power: 30kw: Outlet Size: 200-300mm: Body Liner: SAIL Hard: Body Thickness: 10 mm Plate: Bearing Size: 23222MBKW (URB Romania Made) Maximum feed size: 125 mm: Product size (-) 6 mm: Rotor Size: 850 Dia X 500 mm: Rotor Speed: 400 to 600 RPM: Beater: Manganese 500 X 5 Nos (Impact Plate)

  • Calculating Motor Hp Requirement For Coal Crushers

    coal crusher power calculation. Power to be transmitted = 450 Hp InfoMine . Coal plants will use roll crushers, either single roll or How the the rock crusher motor power is

  • coal crusher rpm Induzin

    coal coal crusher rpm. Coal Crusher Rpm. Coal crusher management failure of coal crusher bearings case study jul 26 2013 this case is related to a coal crusher with crushing capacity of 5060 tonnes per hour the prime mover of the crusher incorporated a 50 h p motor and operated at 500 rpm the crusher was operated through belts and pulleys on both sides and supportedget price

  • Dynamic Analysis on Hammer of a Coal-Hammer Mill Crusher

    6. Overall dimensions of Crusher and its weight. 4. Data considered for Design 1. Type of material being crushed coal 2. Size of material 200 mm taken to 30 mm crush size 3. Capacity / thorough put 16 to25 ton/hour 4. Type of feeding from top 5. Motor rotational speed 970 rpm 6. Overall dimensions of Crusher 980*890*570 mm

  • Coal Crusher Vibration & Dynamic Forces Caused By Misalignment

    Route Spectrum 11-Jul-05 08:04:30 OVERALL= .7287 V-DG PK = .7267 LOAD = 5.0 RPM = 1799. (29.98 Hz) 0 1000 2000 3000 4000 10-4 10-3 10-2 10-1 10 0 10 1 Frequency in CPM PK Velocity in In/Sec Freq: Ordr: Spec: 440.63 .245 .649 Note indication of a resonance between 1X & 2X Crusher Shaft RPM. Expand to Display 4000 CPM Fmax

  • Impact Crusher an overview ScienceDirect Topics

    The speed of the rotor varies between 500 and 3,000 rpm. Due to the high rate of wear on these machines (wear can be taken up by moving the hammers on the pins) they are limited in use to relatively non-abrasive materials. They have extensive use in limestone quarrying and in the crushing of coal. A great advantage in quarrying is the fact that they produce a relatively cubic product.

  • Calculating Motor Hp Requirement For Coal Crushers

    coal crusher power calculation. Power to be transmitted = 450 Hp InfoMine . Coal plants will use roll crushers, either single roll or How the the rock crusher motor power is

  • Coal comminution and sizing ScienceDirect

    01/01/2013· A rotary breaker will rotate at approximately 12–14 RPM (Pennsylvania Crusher, 2011). The feed to a rotary breaker can consist of quite large particles, with increased feed topsize requiring larger-diameter breakers. An 8-foot diameter breaker can handle a topsize of approximately 15 inches, while a 12-foot diameter unit can break coal lumps as large as 30 inches

  • Pulverizer Application for High Volatile High Moisture Coals

    CRUSHER HAMMER Rotate at 900 RPM @ CRUSHED a DRIED COAL Figure 2. HISTORY: Crusher Dryer Riley Stoker Corporation recognized the need for pre-drying of coal a number of years ago in two areas of application: 1. Coals with high equilibrium and/or surface moisture. 2. Coals to be slurried and de-watered at plant site. Conventional coal drying techniques are slow, requiring large equipment to

  • Design and Analysis of Rotor Shaft Assembly of Hammer Mill

    (100kg/hr) tones per hour transmitting 20 B.H.P and a speed of 750 rpm. The design is based on the standard design procedure. In the present work by using the standard design procedure, diameter of rotor shaft of hammer mill crusher has been designed.The

  • Primary Crusher Selection & Design

    23/12/2015· A crusher’s wear parts need to last as long as operationally-economically possible. Typical numbers are for liner and mantles to have a useful wear-life of almost 2,000,000 tonne on abrasive taconite and 9,000,000 tonnes on porphyry copper ores. Dependability and long service life are landmarks of good primary crusher design of up to 30 yrs. The selection of the primary crusher must

  • Jaw crusher SlideShare

    14/11/2015· The compressive strength of jaw crushers is 320 mega Pascal and the Rpm of jaw crusher is between 200- 400. The jaw crusher is used for crushing trash, making it easy for transportation from one to another location. This is very important because the crushed materials are always easier for transportation, loading and dumping. This machine is heavily used on construction sites where a large