ABOUT

Solutions & Cases

Our Case
  • Finishing Mill/ Block Mill (Morgan)- Bar & Wire Rod

    The finishing mill group is the extra-heavy top cross 45° high-speed wire rod finishing mills designed for the high-speed wire rod production line. The finishing mill group is located in the high-speed wire rod workshop. Rolling by 10 units rack continuous micro-tension rolling mill, rolling the Φ17~Φ21 mm of rolled piece transported from upstream into Φ5.5~Φ16 mm finished wire rod. The mill guaranteed exit

  • Wire Rod Block Mill Hani Tech

    The finishing mill / wire rod mill is located in high-speed wire-rod workshop. Through several unit rack the continuous micro-tension rolling mill will be transported upstream Ø17 ~Ø21mm of rolling, rolling become Ø5.5 ~ Ø16mm finished wire. The working speed of 90m/s, 135m/s etc.

  • finishing mill for high-speed wire rod mill rolling

    31/05/2016· The finishing mill group is the extra-heavy top cross 45° high-speed wire rod finishing mills designed for the high-speed wire rod production line.if interes...

  • Rod Mill an overview ScienceDirect Topics

    In the rod mill, high carbon steel rods about 50 mm diameter and extending the whole length of the mill are used in place of balls. This mill gives a very uniform fine product and power consumption is low, although it is not suitable for very tough materials and the feed should not exceed about 25 mm in size. It is particularly useful with sticky materials which would hold the balls together in aggregates, because

  • Mill finish Wikipedia

    Mill finish is the surface texture (or finish) of metal after it exits a rolling mill, extrusion die, or drawing processes, including sheet, bar, plate, or structural shapes. This texture is usually rough and lacks lustre; it may have spots of oxidation or contamination with mill oil.

  • Wire Rod Mills Hani Tech Bar & Wire Rod Rolling Mill

    Wire rod mills are designed for high-speed wire rod production line of heavy top cross 45° high-speed wire rod finishing mill group. It is located in a high-speed wire rod workshop. Wire rod mills are combined with 10 mills, three φ200 mills, and seven φ150 mills, speed increasing box, support base, arc coupling, waterproof slot, waterproof plate,

  • Morgan Wire Rod Mill High-Speed Wire Rod Rolling Mill

    12/12/2019· Raw materials: the products of the high-speed wire rod rolling mill can be produced from φ 5.5 to φ 14, and the raw materials are mainly continuous casting billets. Technological process: billet preparation, billet heating, steel rolling, and finishing. The Features of Morgan Wire Rod Mill

  • Finishing Mill/ Block Mill (Morgan)- Bar & Wire Rod

    The finishing mill group is located in the high-speed wire rod workshop. Rolling by 10 unit rack continuous micro-tension rolling mill, rolling the Φ17~Φ21 mm of rolled piece transported from upstream into Φ5.5~Φ16 mm finished wire rod. The mill guaranteed exit speed is 90 m/s. (When the specification of the finished product is Φ5.5 mm)

  • PROCESS OF ROLLING MILLS

    25/02/2016· A wire rod rolling mill, for example, gradually reduces the cross-sectional area of a starting billet (e.g., 150 mm square, 10-12 meters long) down to a finished rod (as small as 5.0 mm in

  • Rod Mill an overview ScienceDirect Topics

    Rod mill charges usually occupy about 45% of the internal volume of the mill. A closely packed charge of single sized rods will have a porosity of 9.3%. With a mixed charge of small and large diameter rods, the porosity of a static load could be reduced even further. However, close packing of the charge rarely occurs and an operating bed porosity of 40% is common. Overcharging results in poor

  • finishing mill for high-speed wire rod mill rolling

    31/05/2016· The finishing mill group is the extra-heavy top cross 45° high-speed wire rod finishing mills designed for the high-speed wire rod production line.if interes...

  • Morgan Finishing Mill / Wire Rod Mill Steel Rolling

    The morgan finishing mill/wire rod mill arranged after the No.3 flying shear area and before the cooling device. Its role is to continuously micro tension rolling by 8 rack unit, the rolled piece 15.7 ~ 20.1mm of rolling mill upstream delivery, rolled into 5.5 ~ 16mm finished wire rod. Unit to ensure the exit speed of 90m / s. The total of morgan finishing mill is 10 stands, 5 stands Æ230mill

  • Mill (grinding) Wikipedia

    Rod mill. A rotating drum causes friction and attrition between steel rods and ore particles. [citation needed] But note that the term 'rod mill' is also used as a synonym for a slitting mill, which makes rods of iron or other metal. Rod mills are less common than ball mills for grinding minerals. The rods used in the mill, usually a high-carbon steel, can vary in both the length and the

  • Steel Billets, bars, and rods Britannica

    Rod mills are similar to bar mills at the front end, but the finishing end is different. Rods have a smaller section (5.5 to 15 millimetres in diameter) and are always coiled, while bars are normally shipped in cut length. The final rolling in rod mills often takes place in a close-coupled set of 10 pairs of small rolls (200 and 150 millimetres in diameter); these are all installed in a block

  • Automotive product catalogue ArcelorMittal

    Bar & Billet mill Inspection Finishing US test & TOM Heat Treatment (soft annealing, stress relieving, normalising) Continuous casting billets Billets ˜ 155 ² Wire Rod Mill Wire Rod ˚ 5,5-25 Wire Processing (annealing, pickling, phosphating) by local subcontractor Electric Arc Furnace Ladle furnace Vacuum Degassing Continuous casting billets Billets 140 160² 220² Bar Mill EC & US test

  • Stainless Steel Finishes Explained DIN & ASTM Fractory

    13/09/2019· Mill finish is the basic supply condition for stainless steels, no matter whether they are cold or hot rolled. However, most of these steels require further finishing processes to meet the requirements of certain applications. Here is an in-depth description of the stainless steels that fall into this group according to the table above. 1D Stainless Steel Finish Hot Rolled, Annealed

  • Products Sinopac Limited

    Finishing Bar Rolls Learn more Conventional Grades Light Sections Rod and Bar Mill Rings Cantilever Ring Learn more Conventional Grades Rings Steel Grades Section Sleeves Learn more Rings Special Grades Wire Rod Block Ring Learn more Conventional Grades Rolls Tube Mill PQF & MPM Rolls Learn more Conventional Grades Light Sections Rod and Bar Mill Rings Special Grades Tube Mill SRM,